Experimental study on mitigating wind erosion of calcareous desert sand using spray method for microbially induced calcium carbonate precipitation

Wind erosion is one of the significant natural calamities worldwide, which degrades around one-third of global land. The eroded and suspended soil particles in the environment may cause health hazards, i.e. allergies and respiratory diseases, due to the presence of harmful contaminants, bacteria, and pollens. The present study evaluates the feasibility of microbially induced calcium carbonate precipitation (MICP) technique to mitigate wind-induced erosion of calcareous desert sand (Thar desert of Rajasthan province in India). The temperature during biotreatment was kept at 36 °C to stimulate the average temperature of the Thar desert. The spray method was used for bioaugmentation of Sporosarcina (S.) pasteurii and further treatment using chemical solutions. The chemical solution of 0.25 pore volume was sprayed continuously up to 5 d, 10 d, 15 d, and 20 d, using two different concentration ratios of urea and calcium chloride dihydrate viz 2:1 and 1:1. The biotreated samples were subjected to erosion testing (in the wind tunnel) at different wind speeds of 10 m/s, 20 m/s, and 30 m/s. The unconfined compressive strength of the biocemented crust was measured using a pocket penetrometer. The variation in calcite precipitation and microstructure (including the presence of crystalline minerals) of untreated as well as biotreated sand samples were determined through calcimeter, scanning electron microscope (SEM), and energy-dispersive X-ray spectroscope (EDX). The results demonstrated that the erosion of untreated sand increases with an increase in wind speeds. When compared to untreated sand, a lower erosion was observed in all biocemented sand samples, irrespective of treatment condition and wind speed. It was observed that the sample treated with 1:1 cementation solution for up to 5 d, was found to effectively resist erosion at a wind speed of 10 m/s. Moreover, a significant erosion resistance was ascertained in 15 d and 20 d treated samples at higher wind speeds. The calcite content percentage, thickness of crust, bulk density, and surface strength of biocemented sand were enhanced with the increase in treatment duration. The 1:1 concentration ratio of cementation solution was found effective in improving crust thickness and surface strength as compared to 2:1 concentration ratio of cementation solution. The calcite crystals formation was observed in SEM analysis and calcium peaks were observed in EDX analysis for biotreated sand.     

Process Intensification of Living Cationic Polymerization of Isobutylene by a Flow Reaction System

Increasing the reaction temperature of the living cationic polymerization of isobutylene is crucial for industrial production due to the cost of refrigeration. The reaction temperature increase was achieved with an accelerated reaction rate using a flow reaction system. The polymerization conditions, including the flow reactor design, were based on the results of kinetic studies. Utilizing a milli‐scale flow reactor, polyisobutylene, which has a narrow molecular weight distribution, was obtained within a considerably short residence time at a high temperature. Furthermore, it was confirmed that the value of M_w/M_n correlates with the product of the Reynolds number and the angle of collision.     

Hybrid hydrate processes for CO2/H2 mixture purification: A techno-economic analysis

In this work, hydrate based separation technique was combined with membrane separation and amine-absorption separation technologies to design hybrid processes for separation of CO₂/H₂ mixture. Hybrid processes are designed in the presence of different types of hydrate promoters. The conceptual processes have been developed using Aspen HYSYS. Proposed processes were simulated at different flow rates for the feed stream. A comprehensive cost model was developed for economic analysis of novel processes proposed in this study. Based on the results from process simulation and equipment sizing, the amount of total energy consumption, fixed cost, variable cost, and total cost were calculated per unit weight of captured CO₂ for various flow rates of feed stream and in the presence of different hydrate promoters. Results showed that combination of hydrate formation separation technique with membrane separation technology results in a CO₂ capture process with lowest energy consumption and total cost per unit weight of captured CO₂. As split fraction and heat of hydrate formation increases, the share of hydrate formation section in total energy consumption increases. When TBAB is applied as hydrate promoter, due to its higher hydrate separation efficiency, more amount of CO₂ is captured in hydrate formation section and consequently the total cost for process decreases considerably. Hybrid hydrate-membrane process in the presence of TBAB as hydrate promoter with 29.47 US$/ton CO₂ total cost is the best scheme for hybrid hydrate CO₂ capture process. Total cost for this process is lower than total cost for single MDEA-based absorption process as the mature technology for CO₂ capture.     

稀土灼烧过程温湿度场仿真分析

影响稀土灼烧工艺的因素十分复杂,关系产品质量稳定及能耗,现行工艺存在优化空间。通过剖析灼烧窑中温度和湿度分布状况,运用κ-ε双方程湍流模型、流体传热、多孔介质传热等理论,按特定组分运输模式,建立灼烧过程质量、动量和能量耦合传递数学模型。设置不同边界导入Fluent环境对数学模型进行仿真试验,完成数据处理实现工艺参数优化。结果表明所建模型能准确反映灼烧窑中温湿度场分布及变化,且最终仿真结果与实际灼烧后的产品湿度含量相符合。     

综放面本煤层预抽瓦斯的治理技术

为了极大限度地提高本煤层预抽效果，以马兰煤矿为研究对象，针对目前马兰煤矿的瓦斯赋存情况和现阶段所采取的抽放措施，从抽放钻孔的孔径、孔深、布置方式、封孔质量和增加煤层透气性等方面进行探索。实践表明，以上方法的运用，能够有效地提高本煤层预抽抽放效果，保证工作面安全生产。     

磁悬浮控制力矩陀螺高速转子的高精度位置控制

在受到陀螺效应、动框架效应等影响后产生的磁力非线性问题是磁悬浮控制力矩陀螺(MSCMG)高速转子位置精度下降的主要因素。为解决以上问题,提高转子位置精度,本文分析了转子所受磁力的特性,建立了转子系统非线性动力学模型,提出了神经网络滑模控制方法。设计滑模控制律,采用径向基函数神经网络逼近控制律中的非线性模型,自适应算法根据误差在线调整神经网络的权值,同时可以保证整个系统的稳定性。仿真和实验结果表明,所提出方法的转子位置精度达到99%,稳态误差为0.000 2 mm。神经网络滑模控制可以实现MSCMG转子系统的高精度位置控制。     

Theoretical framework for formulating MIP scheduling models with multiple and non-uniform discrete-time grids

We present a framework for the formulation of MIP scheduling models based on multiple and nonuniform discrete time grids. In a previous work we showed that it is possible to use different (possibly non-uniform) time grids for each task, unit, and material. Here, we generalize these ideas to account for general resources, and a range of processing characteristics such as limited intermediate storage and changeovers. Each resource has its own grid based on resource consumption and availability allowing resource constraints to be modeled more accurately without increasing the number of binary variables. We develop algorithms to define the unit-, task-, material-, and resource-specific grids directly from problem data. Importantly, we prove that the multi-grid formulation is able to find a schedule with the same optimal objective as the discrete-time single-grid model with an arbitrarily fine grid. The proposed framework leads to the formulation of models with reduced number of binary variables and constraints, which are able to find good solutions faster than existing models.     

基于DSP的智能电源控制单元设计与实现

本文利用TI公司TMS320F28335芯片高效的浮点运算能力,结合片上丰富的外设,设计并实现了一种具有高可靠性的智能电源控制单元。该控制单元周期性地对各片上外设进行自检维护,完成多路负载通道控制、电压、电流的实时监控,并对故障进行指示、处理和上报,同时提供人机交互界面更新状态信息。经过验证,该控制单元工作稳定,具备良好的工程应用价值。     

Optimized PI+ load–frequency controller using BWNN approach for an interconnected reheat power system with RFB and hydrogen electrolyser units

This paper investigates a renewable energy resource’s application to the Load–Frequency Control of interconnected power system. The Proportional-Integral (PI) controllers are replaced with Proportional-Integral Plus (PI+) controllers in a two area interconnected thermal power system without/with the fast acting energy storage devices and are designed based on Control Performance Standards (CPS) using conventional/Beta Wavelet Neural Network (BWNN) approaches. The energy storing devices Hydrogen generative Aqua Electroliser (HAE) with Fuel cell and Redox Flow Battery (RFB) are incorporated to the two area interconnected thermal power system to efficiently damp out the electromechanical oscillations in the power system because of their inherent efficient storage capacity in addition to the kinetic energy of the generator rotor, which can share the sudden changes in power requirements. The system was simulated and the frequency deviations in area 1 and area 2 and tie-line power deviations for 5% step- load disturbance in area 1 are obtained. The comparison of frequency deviations and tie-line power deviations of the two area interconnected thermal power system with HAE and RFB designed with BWNN controller reveals that the PI+ controller designed using BWNN approach is found to be superior than that of output response obtained using PI+ controller. Moreover the BWNN based PI+ controller exhibits a better transient and steady state response for the interconnected power system with Hydrogen generative Aqua Electroliser (AE) unit than that of the system with Redox Flow Battery (RFB) unit.     

铜浮选专家控制系统设计与应用

针对国内某选矿厂铜浮选工艺泡沫速率不稳定,精矿品位波动大,回收率不理想等特点,设计了一套浮选专家控制系统,该系统结合泡沫影像分析技术,在线品位分析技术,PID控制与模糊逻辑控制技术。系统架构简明合理,逻辑层次清晰有效,投入运行一段时间后,在不同原矿品位前提下,都能实现稳定泡沫速率,减少精矿品位波动,提高回收率等指标优化,同时药剂添加量也有明显减少。这表明该系统运行效果良好,值得应用推广。